Bigfoot Parts

 
     
    1 - 34 of 34 items
    5th Wheel Gen 2 Key Fob EZ Limit Switch & Pin Four SnapPads for Bigfoot 10" Feet
    5th Wheel Gen 2 Key FobEZ Limit Switch & PinFour SnapPads for Bigfoot 10" Feet
    This Key Fob is designed for use with our 2 nd Generation 5 th Wheel Systems. Easily replace a lost or damaged Key Fob with this item. Key Fob Buttons: • Activation • Auto - Reconnect • Extend / Retract Front Jacks Programming...

    Complete Limit Switch Assembly: Ball Switch Clevis Pin *For use with 7" and 'Flat' 8K Footpads - Not for use with Circular Footpads

    "Put some Bigshoes on your Bigfoot!" Snaps onto the Bigfoot 10" flanged octagonal footpad creating a larger surface area, softer compound for ground contact, and increased lift height! This contains FOUR SnapPads for FOUR 10" flanged octagonal...

    $107.00

    $32.00

    $220.00

    Four SnapPads for Bigfoot 7" Feet Override Tank Assembly Quad System Manual Control Panel
    Four SnapPads for Bigfoot 7" FeetOverride Tank AssemblyQuad System Manual Control Panel

    "Put some Bigshoes on your Bigfoot!" Snaps onto the Bigfoot 7" octagonal footpad creating a larger surface area, softer compound for ground contact, and increased lift height! This contains FOUR SnapPads for FOUR footpads. Features: For 7”...

    This is the standard tank assembly (power unit) for all bigfoot series systems (non EZ). This will work on landing gear jacks as well. This tank assembly however comes with the manual override option for the motor, this enables you to operate the...

    Quad System Manual Control Panel Designed for use with our Quad Pump Manual Leveling Systems, this panel can also be used on our Quad Pump Automatic Leveling Systems(plugs in at sensor location). Operate all four cylinders simultaneously or...

    $160.00

    $620.00

    $270.00

    Single SnapPad for Bigfoot 10" Foot Single SnapPad for Bigfoot 7" Foot Two SnapPads for Bigfoot 10" Feet
    Single SnapPad for Bigfoot 10" FootSingle SnapPad for Bigfoot 7" FootTwo SnapPads for Bigfoot 10" Feet
    "Put some Bigshoes on your Bigfoot!" Snaps onto the Bigfoot 10" flanged octagonal footpad creating a larger surface area, softer compound for ground contact, and increased lift height! This contains one SnapPad for one 10" flanged octagonal...

    "Put some Bigshoes on your Bigfoot!" Snaps onto the Bigfoot 7" octagonal footpad creating a larger surface area, softer compound for ground contact, and increased lift height! This contains one SnapPad for one footpad. Features: For 7”...

    "Put some Bigshoes on your Bigfoot!" Snaps onto the Bigfoot 10" flanged octagonal footpad creating a larger surface area, softer compound for ground contact, and increased lift height! This contains TWO SnapPads for TWO 10" flanged octagonal...

    $65.00

    $45.00

    $115.00

    Two SnapPads for Bigfoot 7" Feet Automatic Control Assembly Tank Assembly
    Two SnapPads for Bigfoot 7" FeetAutomatic Control AssemblyTank Assembly

    "Put some Bigshoes on your Bigfoot!" Snaps onto the Bigfoot 7" octagonal footpad creating a larger surface area, softer compound for ground contact, and increased lift height! This contains TWO SnapPads for TWO footpads. Features: For 7”...

    Panel & Sensor Combo for Automatic Systems. Includes everything you need to convert from the old style Automatic System to the current version. This kit includes the Automatic/Manual Control Panel, Auto Sensor, Interface Harness, Bezel &...

    This is the standard tank assembly (power unit) for all bigfoot series systems (non EZ). This will work on landing gear jacks as well. Assembly includes: pump, motor, reservoir, fill plug, solenoids & tank bracket. Click here for diagram

    $85.00

    $660.00

    $580.00

    Wireless Controller (USB) 5th Wheel Control Panel Auto Panel
    EZ Wireless Control5th Wheel Control PanelAuto Panel
    This is an upgrade for any of our EZ Manual Systems. This is an easy replacement, simply unplug your current control panel harness and plug in the receiver and your done. The hand held remote allows you to walk around the vehicle while you level...This is a replacement Control Panel for the 2nd Generation 5 th Wheel System (both version 1 and 2). Blue tinted LCD screen makes it easier to read in the sun than previous versions.

    Replacement Control Panel for Automatic Systems If your old panel has a Rocker on/off switch instead of a system power button, you will need the entire Upgrade Kit #M37525. Features Manual Mode, All Up & Emergency Retract.

    $395.00

    $255.00

    $255.00

    Wireless 1 Point Control 2 Point Weatherproof Control Box 1 Point Weatherproof Control Box
    Wireless 1 Point Control2 Point Weatherproof Control Box1 Point Weatherproof Control Box

    Wireless Control for your 1 Point or Slave leg jacks. Convert your standard grey box control to a Wireless Key Fob! There are secondary controls on the receiver itself inside the tank assembly if the Key Fob is misplaced or damaged. This is the 3...

    This is the Standard Conrol box for the 2 Point Systems.... This Weatherproof Box includes a momentary toggle switch, long wire harness and a lock & key safety mechanism (with two keys).

    This is the Standard Control Box(Gen. 2) for Single Point and Slave Systems. This Weatherproof Box has 2 push buttons for cylinder operation, a long wire harness and a lock & key safety mechanism (with two keys). Installation is a simple 3-wire connection to the tank assembly.

    $172.00

    $160.00

    $134.00

    EZ Valve/Coil Combo 120 Amp Breaker Square Leg Footpad
    EZ Valve/Coil Combo120 Amp BreakerSquare Leg Footpad

    This Valve/Coil combo is a replacement for each corner jack on all EZ systems(both manual & automatic central pump systems). The only requirement is that it is an Oildyne/Parker Pump motor, this does not work for MTE or Monarch central pump systems.

    This is the standard 120 amp breaker we include in 4 Point, 4 Pump Systems. This is required to be installed between the battery harness from the jacks/pumps and the positive terminal on the house battery.

    Square Leg Footpad Square Leg Pivoting Footpad, will work for all square legs that do not have a fixed foot (welded plate to the inside tube). Assembly comes with the 1" pin & retaining rings.

    $110.00

    $79.00

    $74.00

    10" Footpad (Round Legs) 12 Volt Solenoid EZ Tank Cover
    10" Footpad (Round Legs)12 Volt SolenoidEZ Tank Cover

    This is the standard 10" footpad that comes with all round leg systems. With each footpad will come a bolt and a nut to fit the current style cylinders and retro-fit the previous style cylinders. So this is truly a universal 100 square inch footpad!

    This 12 volt solenoid is what we use on all of our systems. If you have the older style (pre-2001) you need to buy a pair of these for each motor to work properly.

    Tank cover for EZ (standard size) tank assembly. Measurements: 13" wide x 8/14" tall x 5 3/8" deep. Installs with one self-tapping screw in center into reservoir & one or two on each side from tab (screws not included).

    $39.00

    $38.00

    $37.00

    Limit Switch Assembly 2ft QE3/Square Leg Weld-On Bracket Deep Long Bracket
    Limit Switch Assembly 2ftQE3/Square Leg Weld-On BracketDeep Long Bracket

    Complete Limit Switch Assembly: - Ball Switch - Clevis Pin - 2 ft Extension - Proper Wire Connections (attaches to jack, and wires connect to system wire harness & ground)

    QE3/Square Leg Weld-On Bracket This is the weld-on mounting bracket for all QE3 (24k-lb) cylinders AND for all Square Leg 4 Point Systems.This deep long bracket is one of our strongest brackets due to the increased lateral strength from its depth, long design allows for the cylinder to be mounted lower or give it increased backing strength for the large applications. This bracket fits all 8k, QEI & QEII cylinders.

    $36.00

    $36.00

    $28.00

    Inside Mount Bracket Long Standard Bracket 3x7 Mounting Bracket
    Inside Mount BracketLong Standard Bracket3x7 Mounting Bracket
    This weld-on mounting bracket's unique design mounts to the inside of most frame rails. Most of the time this bracket is used in the rear of Ford Class C/B motorhomes. For use with all 8k & QEI cylinders.Weld-on mounting bracket for all 8k, QEI & QEII cylinders. This low profile bracket helps with tight clearances from the frame to a storage box or tank, also long design allows for cylinder to be mounted lower on the frame for increased lift....Weld-on Bracket for mounting round leg jacks to your coach. This bracket is usually found on the front of Ford Class C/B motorhomes & the rear of 5th Wheels. But this bracket accommodates for many applications. For use with all 8k, QEI & QEII cylinders.

    $24.00

    $23.00

    $19.00

    Tank Cover (new) Tank Cover (old) Standard Bracket
    Tank Cover (new)Tank Cover (old)Standard Bracket

    Tank cover for plastic reservoir tank assemblies. Measurements: 9 " wide x 12 1/2" tall x 5 3/4" deep. Installs with two self-tapping screws (not included). NO SLOT

    Tank cover for steel reservoir tank assemblies. (not EZ) Measurements: 8 1/4" wide x 12 1/2" tall x 5 3/4" deep. Installs with two self-tapping screws (not included). NO SLOT

    This is our standard bracket, simple 7x7 size that is low profile for those tight spaces between the frame and a storage box or tank. This bracket fits all 8k & QEI cylinders.

    $18.00

    $18.00

    $18.00

    JIC Elbow Fitting
    JIC Elbow Fitting

    Standard elbow fitting on all cylinders, works with all current style hoses (flex line).

    $4.00