Bigfoot Parts

 
     
    1 - 24 of 26 items
    EZ Limit Switch & Pin Override Tank Assembly Automatic Control Assembly
    EZ Limit Switch & PinOverride Tank AssemblyAutomatic Control Assembly

    Complete Limit Switch Assembly: Ball Switch Clevis Pin *For use with 7" and 'Flat' 8K Footpads - Not for use with Circular Footpads

    This is the standard tank assembly (power unit) for all bigfoot series systems (non EZ). This will work on landing gear jacks as well. This tank assembly however comes with the manual override option for the motor, this enables you to operate the...

    Panel & Sensor Combo for Automatic Systems. Includes everything you need to convert from the old style Automatic System to the current version. This kit includes the Automatic/Manual Control Panel, Auto Sensor, Interface Harness, Bezel &...

    $32.00

    $620.00

    $660.00

    Tank Assembly EZ Wireless Control 5th Wheel Control Panel
    Tank AssemblyEZ Wireless Control5th Wheel Control Panel

    This is the standard tank assembly (power unit) for all bigfoot series systems (non EZ). This will work on landing gear jacks as well. Assembly includes: pump, motor, reservoir, fill plug, solenoids & tank bracket. Click here for diagram

    This is an upgrade for any of our EZ manual systems. This is a simple replacement. Simply unplug your current control panel harness and plug in the receiver and your done. The new hand held remote allows you to walk around the vehicle while you...

    This is a replacement control panel for the 2nd generation 5th wheel system (both version 1 and 2). Blue tinted LCD screen makes it easier to read in the sun than previous versions.

    $580.00

    $395.00

    $255.00

    Auto Panel Wireless 1 Point Control 2 Point Weatherproof Control Box
    Auto PanelWireless 1 Point Control2 Point Weatherproof Control Box
    Replacement Control Panel for Automatic Systems If your old panel has a Rocker on/off switch instead of a system power button, you will need the entire Upgrade Kit #M37525. Features Manual Mode, All Up & Emergency Retract.

    Wireless Control for your 1 Point or Slave leg jacks. Convert your standard grey box control to a Wireless Key Fob! There are secondary controls on the receiver itself inside the tank assembly if the Key Fob is misplaced or damaged. This is the 3...

    This is the Standard Conrol box for the 2 Point Systems.... This Weatherproof Box includes a momentary toggle switch, long wire harness and a lock & key safety mechanism (with two keys).

    $255.00

    $172.00

    $160.00

    1 Point Weatherproof Control Box EZ Valve/Coil Combo 120 Amp Breaker
    1 Point Weatherproof Control BoxEZ Valve/Coil Combo120 Amp Breaker
    This is the Standard Control Box(Gen. 2) for Single Point and Slave Systems. This Weatherproof Box has 2 push buttons for cylinder operation, a long wire harness and a lock & key safety mechanism (with two keys). Installation is a simple 3-wire connection to the tank assembly.

    This Valve/Coil combo is a replacement for each corner jack on all EZ systems(both manual & automatic central pump systems). The only requirement is that it is an Oildyne/Parker Pump motor, this does not work for MTE or Monarch central pump systems.

    This is the standard 120 amp breaker we include in 4 Point, 4 Pump Systems. This is required to be installed between the battery harness from the jacks/pumps and the positive terminal on the house battery.

    $134.00

    $110.00

    $79.00

    Square Leg Footpad 10" Footpad (Round Legs) 12 Volt Solenoid
    Square Leg Footpad10" Footpad (Round Legs)12 Volt Solenoid
    Square Leg Footpad Square Leg Pivoting Footpad, will work for all square legs that do not have a fixed foot (welded plate to the inside tube). Assembly comes with the 1" pin & retaining rings.

    This is the standard 10" footpad that comes with all round leg systems. With each footpad will come a bolt and a nut to fit the current style cylinders and retro-fit the previous style cylinders. So this is truly a universal 100 square inch footpad!

    This 12 volt solenoid is what we use on all of our systems. If you have the older style (pre-2001) you need to buy a pair of these for each motor to work properly.

    $74.00

    $39.00

    $38.00

    EZ Tank Cover Limit Switch Assembly 2ft QE3/Square Leg Weld-On Bracket
    EZ Tank CoverLimit Switch Assembly 2ftQE3/Square Leg Weld-On Bracket

    Tank cover for EZ (standard size) tank assembly. Measurements: 13" wide x 8/14" tall x 5 3/8" deep. Installs with one self-tapping screw in center into reservoir & one or two on each side from tab (screws not included).

    Complete Limit Switch Assembly: - Ball Switch - Clevis Pin - 2 ft Extension - Proper Wire Connections (attaches to jack, and wires connect to system wire harness & ground)

    QE3/Square Leg Weld-On Bracket This is the weld-on mounting bracket for all QE3 (24k-lb) cylinders AND for all Square Leg 4 Point Systems.

    $37.00

    $36.00

    $36.00

    Deep Long Bracket Inside Mount Bracket Long Standard Bracket
    Deep Long BracketInside Mount BracketLong Standard Bracket
    This deep long bracket is one of our strongest brackets due to the increased lateral strength from its depth, long design allows for the cylinder to be mounted lower or give it increased backing strength for the large applications. This bracket fits all 8k, QEI & QEII cylinders.This weld-on mounting bracket's unique design mounts to the inside of most frame rails. Most of the time this bracket is used in the rear of Ford Class C/B motorhomes. For use with all 8k & QEI cylinders.Weld-on mounting bracket for all 8k, QEI & QEII cylinders. This low profile bracket helps with tight clearances from the frame to a storage box or tank, also long design allows for cylinder to be mounted lower on the frame for increased lift....

    $28.00

    $24.00

    $23.00

    3x7 Mounting Bracket Tank Cover (new) Tank Cover (old)
    3x7 Mounting BracketTank Cover (new)Tank Cover (old)
    Weld-on Bracket for mounting round leg jacks to your coach. This bracket is usually found on the front of Ford Class C/B motorhomes & the rear of 5th Wheels. But this bracket accommodates for many applications. For use with all 8k, QEI & QEII cylinders.

    Tank cover for plastic reservoir tank assemblies. Measurements: 9 " wide x 12 1/2" tall x 5 3/4" deep. Installs with two self-tapping screws (not included). NO SLOT

    Tank cover for steel reservoir tank assemblies. (not EZ) Measurements: 8 1/4" wide x 12 1/2" tall x 5 3/4" deep. Installs with two self-tapping screws (not included). NO SLOT

    $19.00

    $18.00

    $18.00